[WARNING]: Could not match supplied host pattern, ignoring: unprovisioned PLAY [Deploy initial device configuration] ************************************* TASK [Set variables that cannot be set with VARS] ****************************** ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Find device readiness script] ******************************************** ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Wait for device to become ready] ***************************************** skipping: [h1] skipping: [h2] skipping: [h3] skipping: [h4] included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/routeros7.yml for s1 TASK [Execute local ssh command to check router readiness] ********************* skipping: [s1] TASK [Deploy initial configuration] ******************************************** included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for h1, h2, h3, h4, s1 TASK [Figure out whether to deploy the module initial on current device] ******* ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Find configuration template for initial] ********************************* ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Print deployed configuration when running in verbose mode] *************** ok: [h1] => msg: |- initial configuration for h1 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing # ip link set dev eth1 up set +e ip addr del 172.16.0.1/24 dev eth1 2>/dev/null set -e ip addr add 172.16.0.1/24 dev eth1 ip link set eth1 mtu 1500 # # Add routes to IPv4 address pools pointing to the first neighbor on the first link # # If you need anything better, use FRR instead of Linux and start routing (or use IPv6) # # # Print the final routing table ip route ok: [h2] => msg: |- initial configuration for h2 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing # ip link set dev eth1 up set +e ip addr del 172.16.0.2/24 dev eth1 2>/dev/null set -e ip addr add 172.16.0.2/24 dev eth1 ip link set eth1 mtu 1500 # # Add routes to IPv4 address pools pointing to the first neighbor on the first link # # If you need anything better, use FRR instead of Linux and start routing (or use IPv6) # # # Print the final routing table ip route ok: [h3] => msg: |- initial configuration for h3 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing # ip link set dev eth1 up set +e ip addr del 172.16.1.3/24 dev eth1 2>/dev/null set -e ip addr add 172.16.1.3/24 dev eth1 ip link set eth1 mtu 1500 # # Add routes to IPv4 address pools pointing to the first neighbor on the first link # # If you need anything better, use FRR instead of Linux and start routing (or use IPv6) # # lan prefix: 172.16.0.0/16 local subnet: 172.16.1.0/24 set +e ip route del 172.16.0.0/16 2>/dev/null set -e ip route add 172.16.0.0/16 via 172.16.1.5 # loopback prefix: 10.0.0.0/24 local subnet: 172.16.1.0/24 set +e ip route del 10.0.0.0/24 2>/dev/null set -e ip route add 10.0.0.0/24 via 172.16.1.5 # mgmt prefix: 192.168.17.0/24 local subnet: 172.16.1.0/24 # p2p prefix: 10.1.0.0/16 local subnet: 172.16.1.0/24 set +e ip route del 10.1.0.0/16 2>/dev/null set -e ip route add 10.1.0.0/16 via 172.16.1.5 # router_id prefix: 10.0.0.0/24 local subnet: 172.16.1.0/24 # vrf_loopback prefix: 10.2.0.0/24 local subnet: 172.16.1.0/24 set +e ip route del 10.2.0.0/24 2>/dev/null set -e ip route add 10.2.0.0/24 via 172.16.1.5 # # Print the final routing table ip route ok: [h4] => msg: |- initial configuration for h4 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing # ip link set dev eth1 up set +e ip addr del 172.16.2.4/24 dev eth1 2>/dev/null set -e ip addr add 172.16.2.4/24 dev eth1 ip link set eth1 mtu 1500 # # Add routes to IPv4 address pools pointing to the first neighbor on the first link # # If you need anything better, use FRR instead of Linux and start routing (or use IPv6) # # lan prefix: 172.16.0.0/16 local subnet: 172.16.2.0/24 set +e ip route del 172.16.0.0/16 2>/dev/null set -e ip route add 172.16.0.0/16 via 172.16.2.5 # loopback prefix: 10.0.0.0/24 local subnet: 172.16.2.0/24 set +e ip route del 10.0.0.0/24 2>/dev/null set -e ip route add 10.0.0.0/24 via 172.16.2.5 # mgmt prefix: 192.168.17.0/24 local subnet: 172.16.2.0/24 # p2p prefix: 10.1.0.0/16 local subnet: 172.16.2.0/24 set +e ip route del 10.1.0.0/16 2>/dev/null set -e ip route add 10.1.0.0/16 via 172.16.2.5 # router_id prefix: 10.0.0.0/24 local subnet: 172.16.2.0/24 # vrf_loopback prefix: 10.2.0.0/24 local subnet: 172.16.2.0/24 set +e ip route del 10.2.0.0/24 2>/dev/null set -e ip route add 10.2.0.0/24 via 172.16.2.5 # # Print the final routing table ip route ok: [s1] => msg: |- initial configuration for s1 ========================================= /system identity set name="s1" /interface bridge add name=loopback protocol-mode=none /ip address add interface=loopback address=10.0.0.5/32 /interface/bridge/add name=switch vlan-filtering=yes comment="Global Switch Bridge" /interface/vlan/add name=vlan1001 vlan-id=1001 interface=switch /interface/vlan/add name=vlan1002 vlan-id=1002 interface=switch /interface/vlan/add name=vlan1000 vlan-id=1000 interface=switch /interface ethernet set comment="VLAN red (1000) -> [h1,h2] [stub]" vlan1000 /interface ethernet set comment="VLAN blue (1001) -> [h3] [stub]" vlan1001 /ip address add interface=vlan1001 address=172.16.1.5/24 /ip address set [find where interface=vlan1001] comment="VLAN blue (1001) -> [h3] [stub]" /interface ethernet set comment="VLAN green (1002) -> [h4] [stub]" vlan1002 /ip address add interface=vlan1002 address=172.16.2.5/24 /ip address set [find where interface=vlan1002] comment="VLAN green (1002) -> [h4] [stub]" /ip neighbor discovery-settings set discover-interface-list=all TASK [Find configuration deployment deploy_script for initial] ***************** ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Deploy initial configuration] ******************************************** included: /home/pipi/net101/tools/netsim/ansible/tasks/linux/initial-clab.yml for h1, h2, h3, h4 included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/routeros7.yml for s1 TASK [set_fact] **************************************************************** ok: [h1] ok: [h2] ok: [h3] ok: [h4] TASK [Create initial container setup from /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2] *** changed: [h3 -> localhost] changed: [h2 -> localhost] changed: [h1 -> localhost] changed: [h4 -> localhost] TASK [Initial container configuration via /tmp/config-KMpRACQB-h1.sh] ********** changed: [h1 -> localhost] changed: [h2 -> localhost] changed: [h3 -> localhost] changed: [h4 -> localhost] TASK [file] ******************************************************************** changed: [h3 -> localhost] changed: [h1 -> localhost] changed: [h4 -> localhost] changed: [h2 -> localhost] TASK [load initial from /home/pipi/net101/tools/netsim/ansible/templates/initial/routeros7.j2] *** ok: [s1] TASK [Run commands on CHR] ***************************************************** changed: [s1] PLAY [Deploy module-specific configurations] *********************************** TASK [Set variables that cannot be set with VARS] ****************************** ok: [s1] TASK [Deploy individual configuration modules] ********************************* included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for s1 => (item=vlan) TASK [Figure out whether to deploy the module vlan on current device] ********** ok: [s1] TASK [Find configuration template for vlan] ************************************ ok: [s1] TASK [Print deployed configuration when running in verbose mode] *************** ok: [s1] => msg: |- vlan configuration for s1 ========================================= /interface/bridge/vlan add bridge=switch vlan-ids=1001 tagged=switch /interface/bridge/vlan add bridge=switch vlan-ids=1002 tagged=switch /interface/bridge/vlan add bridge=switch vlan-ids=1000 tagged=switch /interface/bridge/port add bridge=switch interface=ether2 pvid=1000 /interface/bridge/vlan set untagged=([get value-name=untagged [find vlan-ids=1000]],"ether2") [find vlan-ids=1000] /interface/bridge/port add bridge=switch interface=ether3 pvid=1000 /interface/bridge/vlan set untagged=([get value-name=untagged [find vlan-ids=1000]],"ether3") [find vlan-ids=1000] /interface/bridge/port add bridge=switch interface=ether4 pvid=1001 /interface/bridge/vlan set untagged=([get value-name=untagged [find vlan-ids=1001]],"ether4") [find vlan-ids=1001] /interface/bridge/port add bridge=switch interface=ether5 pvid=1002 /interface/bridge/vlan set untagged=([get value-name=untagged [find vlan-ids=1002]],"ether5") [find vlan-ids=1002] TASK [Find configuration deployment deploy_script for vlan] ******************** ok: [s1] TASK [Deploy vlan configuration] *********************************************** included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/routeros7.yml for s1 TASK [load vlan from /home/pipi/net101/tools/netsim/ansible/templates/vlan/routeros7.j2] *** ok: [s1] TASK [Run commands on CHR] ***************************************************** changed: [s1] PLAY [Deploy custom deployment templates] ************************************** skipping: no hosts matched PLAY RECAP ********************************************************************* h1 : ok=12 changed=3 unreachable=0 failed=0 skipped=1 rescued=0 ignored=0 h2 : ok=12 changed=3 unreachable=0 failed=0 skipped=1 rescued=0 ignored=0 h3 : ok=12 changed=3 unreachable=0 failed=0 skipped=1 rescued=0 ignored=0 h4 : ok=12 changed=3 unreachable=0 failed=0 skipped=1 rescued=0 ignored=0 s1 : ok=20 changed=2 unreachable=0 failed=0 skipped=1 rescued=0 ignored=0 The device under test is a mixed layer-2/layer-3 switch. Red VLAN is a layer-2-only VLAN, the device acts as a L2/L3 switch on all other VLANs h1 and h2 should be able to ping each other, but not h3 or h4 h3 and h4 should be able to ping each other, but not h1 or h2