[WARNING]: Could not match supplied host pattern, ignoring: unprovisioned

PLAY [Deploy initial device configuration] *************************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [r1]
ok: [r2]
ok: [r4]
ok: [r3]
ok: [dut]

TASK [Find device readiness script] ********************************************
ok: [r1]
ok: [r2]
ok: [r3]
ok: [r4]
ok: [dut]

TASK [Wait for device to become ready] *****************************************
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]
included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/routeros7.yml for dut

TASK [Execute local ssh command to check router readiness] *********************
skipping: [dut]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r1, r2, r3, r4

TASK [Figure out whether to deploy the module initial on current device] *******
ok: [r1]
ok: [r2]
ok: [r4]
ok: [r3]
ok: [dut]

TASK [Find configuration template for initial] *********************************
ok: [r1]
ok: [r2]
ok: [r3]
ok: [r4]
ok: [dut]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [dut] => 
  msg: |-
    initial configuration for dut
    =========================================
  
    /system identity set name="dut"
  
    /interface bridge add name=loopback protocol-mode=none
  
    /interface bridge add name=loopback1 protocol-mode=none
    /interface bridge add name=loopback2 protocol-mode=none
  
    /ip address add interface=loopback address=10.0.0.1/32
  
  
  
  
  
  
  
    /ip/vrf/add place-before=0 name=blue interfaces=ether4,ether5,loopback2
  
  
  
  
  
  
    /ip/vrf/add place-before=0 name=red interfaces=ether2,ether3,loopback1
  
  
  
    /interface ethernet set comment="dut -> r1 [external]" ether2
  
  
    /ip address add interface=ether2 address=172.16.0.1/24
    /ip address set [find where interface=ether2] comment="dut -> r1 [external]"
  
  
    /interface ethernet set comment="dut -> r2 [external]" ether3
  
  
    /ip address add interface=ether3 address=172.16.1.1/24
    /ip address set [find where interface=ether3] comment="dut -> r2 [external]"
  
  
    /interface ethernet set comment="dut -> r3 [external]" ether4
  
  
    /ip address add interface=ether4 address=172.16.2.1/24
    /ip address set [find where interface=ether4] comment="dut -> r3 [external]"
  
  
    /interface ethernet set comment="dut -> r4 [external]" ether5
  
  
    /ip address add interface=ether5 address=172.16.3.1/24
    /ip address set [find where interface=ether5] comment="dut -> r4 [external]"
  
  
    /interface ethernet set comment="VRF Loopback red" loopback1
  
  
    /ip address add interface=loopback1 address=10.0.0.42/32
    /ip address set [find where interface=loopback1] comment="VRF Loopback red"
  
  
    /interface ethernet set comment="VRF Loopback blue" loopback2
  
  
    /ip address add interface=loopback2 address=10.0.0.43/32
    /ip address set [find where interface=loopback2] comment="VRF Loopback blue"
  
  
    /ip neighbor discovery-settings set discover-interface-list=all
ok: [r1] => 
  msg: |-
    initial configuration for r1
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)#"
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # Build hosts file
    #
    echo "# Created by netlab initial" >>/tmp/hosts
    echo "10.0.0.1 dut" >>/tmp/hosts
    echo "172.16.2.1 172.16.3.1 10.0.0.43 dut-blue" >>/tmp/hosts
    echo "172.16.0.1 172.16.1.1 10.0.0.42 dut-red" >>/tmp/hosts
    echo "10.0.0.2 172.16.0.2 r1" >>/tmp/hosts
    echo "10.0.0.3 172.16.1.3 r2" >>/tmp/hosts
    echo "10.0.0.4 172.16.2.4 r3" >>/tmp/hosts
    echo "10.0.0.5 172.16.3.5 r4" >>/tmp/hosts
    grep "Created by netlab" /etc/hosts || uniq /tmp/hosts|sort >>/etc/hosts
  
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    #
    # Create loopbacks and stub devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
    #
    # Set Ethernet interface MTU
    ip link set eth1 mtu 1500
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r1
    !
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.2/32
    !
    interface eth1
     no shutdown
     description r1 -> dut [external]
     ip address 172.16.0.2/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [r2] => 
  msg: |-
    initial configuration for r2
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)#"
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # Build hosts file
    #
    echo "# Created by netlab initial" >>/tmp/hosts
    echo "10.0.0.1 dut" >>/tmp/hosts
    echo "172.16.2.1 172.16.3.1 10.0.0.43 dut-blue" >>/tmp/hosts
    echo "172.16.0.1 172.16.1.1 10.0.0.42 dut-red" >>/tmp/hosts
    echo "10.0.0.2 172.16.0.2 r1" >>/tmp/hosts
    echo "10.0.0.3 172.16.1.3 r2" >>/tmp/hosts
    echo "10.0.0.4 172.16.2.4 r3" >>/tmp/hosts
    echo "10.0.0.5 172.16.3.5 r4" >>/tmp/hosts
    grep "Created by netlab" /etc/hosts || uniq /tmp/hosts|sort >>/etc/hosts
  
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    #
    # Create loopbacks and stub devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
    #
    # Set Ethernet interface MTU
    ip link set eth1 mtu 1500
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r2
    !
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.3/32
    !
    interface eth1
     no shutdown
     description r2 -> dut [external]
     ip address 172.16.1.3/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [r3] => 
  msg: |-
    initial configuration for r3
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)#"
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # Build hosts file
    #
    echo "# Created by netlab initial" >>/tmp/hosts
    echo "10.0.0.1 dut" >>/tmp/hosts
    echo "172.16.2.1 172.16.3.1 10.0.0.43 dut-blue" >>/tmp/hosts
    echo "172.16.0.1 172.16.1.1 10.0.0.42 dut-red" >>/tmp/hosts
    echo "10.0.0.2 172.16.0.2 r1" >>/tmp/hosts
    echo "10.0.0.3 172.16.1.3 r2" >>/tmp/hosts
    echo "10.0.0.4 172.16.2.4 r3" >>/tmp/hosts
    echo "10.0.0.5 172.16.3.5 r4" >>/tmp/hosts
    grep "Created by netlab" /etc/hosts || uniq /tmp/hosts|sort >>/etc/hosts
  
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    #
    # Create loopbacks and stub devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
    #
    # Set Ethernet interface MTU
    ip link set eth1 mtu 1500
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r3
    !
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.4/32
    !
    interface eth1
     no shutdown
     description r3 -> dut [external]
     ip address 172.16.2.4/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0
ok: [r4] => 
  msg: |-
    initial configuration for r4
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)#"
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # Build hosts file
    #
    echo "# Created by netlab initial" >>/tmp/hosts
    echo "10.0.0.1 dut" >>/tmp/hosts
    echo "172.16.2.1 172.16.3.1 10.0.0.43 dut-blue" >>/tmp/hosts
    echo "172.16.0.1 172.16.1.1 10.0.0.42 dut-red" >>/tmp/hosts
    echo "10.0.0.2 172.16.0.2 r1" >>/tmp/hosts
    echo "10.0.0.3 172.16.1.3 r2" >>/tmp/hosts
    echo "10.0.0.4 172.16.2.4 r3" >>/tmp/hosts
    echo "10.0.0.5 172.16.3.5 r4" >>/tmp/hosts
    grep "Created by netlab" /etc/hosts || uniq /tmp/hosts|sort >>/etc/hosts
  
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    #
    # Create loopbacks and stub devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
    #
    # Set Ethernet interface MTU
    ip link set eth1 mtu 1500
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r4
    !
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.5/32
    !
    interface eth1
     no shutdown
     description r4 -> dut [external]
     ip address 172.16.3.5/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0

TASK [Find configuration deployment deploy_script for initial] *****************
ok: [r1]
ok: [r2]
ok: [r4]
ok: [dut]
ok: [r3]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/routeros7.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/frr/initial-clab.yml for r1, r2, r3, r4

TASK [load initial from /home/pipi/net101/tools/netsim/ansible/templates/initial/routeros7.j2] ***
ok: [dut]

TASK [Run commands on CHR] *****************************************************
changed: [dut]

TASK [Attempt to load VRF kernel module] ***************************************
changed: [r3 -> localhost]
changed: [r1 -> localhost]
changed: [r4 -> localhost]
changed: [r2 -> localhost]

TASK [Disable FRR management VRF when modprobe fails] **************************
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]

TASK [include_tasks] ***********************************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/frr/deploy-config.yml for r1, r2, r3, r4

TASK [template] ****************************************************************
changed: [r1]
changed: [r3]
changed: [r4]
changed: [r2]

TASK [set_fact] ****************************************************************
ok: [r1]
ok: [r2]
ok: [r3]
ok: [r4]

TASK [run /tmp/config.sh to deploy initial config from /home/pipi/net101/tools/netsim/ansible/templates/initial/frr.j2] ***
changed: [r1]
changed: [r3]
changed: [r2]
changed: [r4]

TASK [run vtysh to import initial config from /home/pipi/net101/tools/netsim/ansible/templates/initial/frr.j2] ***
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]

PLAY [Deploy module-specific configurations] ***********************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [r1]
ok: [r2]
ok: [r4]
ok: [r3]
ok: [dut]

TASK [Deploy individual configuration modules] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r1, r2, r3, r4 => (item=bgp)
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, r1, r2, r3, r4 => (item=vrf)

TASK [Figure out whether to deploy the module bgp on current device] ***********
ok: [r1]
ok: [r2]
ok: [r3]
ok: [dut]
ok: [r4]

TASK [Find configuration template for bgp] *************************************
ok: [r1]
ok: [r2]
ok: [r3]
ok: [dut]
ok: [r4]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [r1] => 
  msg: |-
    bgp configuration for r1
    =========================================
    !
    router bgp 65101
      no bgp ebgp-requires-policy
      no bgp default ipv4-unicast
      bgp default show-hostname
      bgp default show-nexthop-hostname
  
      ! Consider AS paths of same length but with different AS as ECMP candidates
      bgp bestpath as-path multipath-relax
  
      bgp router-id 10.0.0.2
    !
      neighbor 172.16.0.1 remote-as 65000
      neighbor 172.16.0.1 description dut
    !
     address-family ipv4 unicast
    !
      network 10.0.0.2/32
    !
    !
    !
      neighbor 172.16.0.1 activate
      no neighbor 172.16.0.1 send-community all
      neighbor 172.16.0.1 send-community standard
      neighbor 172.16.0.1 send-community large
    !
    !
    !
    do write
ok: [r2] => 
  msg: |-
    bgp configuration for r2
    =========================================
    !
    router bgp 65102
      no bgp ebgp-requires-policy
      no bgp default ipv4-unicast
      bgp default show-hostname
      bgp default show-nexthop-hostname
  
      ! Consider AS paths of same length but with different AS as ECMP candidates
      bgp bestpath as-path multipath-relax
  
      bgp router-id 10.0.0.3
    !
      neighbor 172.16.1.1 remote-as 65000
      neighbor 172.16.1.1 description dut
    !
     address-family ipv4 unicast
    !
      network 10.0.0.3/32
    !
    !
    !
      neighbor 172.16.1.1 activate
      no neighbor 172.16.1.1 send-community all
      neighbor 172.16.1.1 send-community standard
      neighbor 172.16.1.1 send-community large
    !
    !
    !
    do write
ok: [r3] => 
  msg: |-
    bgp configuration for r3
    =========================================
    !
    router bgp 65103
      no bgp ebgp-requires-policy
      no bgp default ipv4-unicast
      bgp default show-hostname
      bgp default show-nexthop-hostname
  
      ! Consider AS paths of same length but with different AS as ECMP candidates
      bgp bestpath as-path multipath-relax
  
      bgp router-id 10.0.0.4
    !
      neighbor 172.16.2.1 remote-as 65000
      neighbor 172.16.2.1 description dut
    !
     address-family ipv4 unicast
    !
      network 10.0.0.4/32
    !
    !
    !
      neighbor 172.16.2.1 activate
      no neighbor 172.16.2.1 send-community all
      neighbor 172.16.2.1 send-community standard
      neighbor 172.16.2.1 send-community large
    !
    !
    !
    do write
ok: [dut] => 
  msg: |-
    bgp configuration for dut
    =========================================
  
    /routing/bgp/template add name=main as=65000 output.network=bgp-networks
  
    /routing/bgp/template set main router-id=10.0.0.1
  
  
  
    # BGP Network now is controlled by simple ACL
    /ip/firewall/address-list/ add list=bgp-networks address=10.0.0.1/32
ok: [r4] => 
  msg: |-
    bgp configuration for r4
    =========================================
    !
    router bgp 65104
      no bgp ebgp-requires-policy
      no bgp default ipv4-unicast
      bgp default show-hostname
      bgp default show-nexthop-hostname
  
      ! Consider AS paths of same length but with different AS as ECMP candidates
      bgp bestpath as-path multipath-relax
  
      bgp router-id 10.0.0.5
    !
      neighbor 172.16.3.1 remote-as 65000
      neighbor 172.16.3.1 description dut
    !
     address-family ipv4 unicast
    !
      network 10.0.0.5/32
    !
    !
    !
      neighbor 172.16.3.1 activate
      no neighbor 172.16.3.1 send-community all
      neighbor 172.16.3.1 send-community standard
      neighbor 172.16.3.1 send-community large
    !
    !
    !
    do write

TASK [Find configuration deployment deploy_script for bgp] *********************
ok: [r1]
ok: [r2]
ok: [r3]
ok: [dut]
ok: [r4]

TASK [Deploy bgp configuration] ************************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/routeros7.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/frr.yml for r1, r2, r3, r4

TASK [load bgp from /home/pipi/net101/tools/netsim/ansible/templates/bgp/routeros7.j2] ***
ok: [dut]

TASK [Run commands on CHR] *****************************************************
changed: [dut]

TASK [template] ****************************************************************
changed: [r2]
changed: [r1]
changed: [r3]
changed: [r4]

TASK [set_fact] ****************************************************************
ok: [r1]
ok: [r2]
ok: [r4]
ok: [r3]

TASK [run /tmp/config.sh to deploy bgp config from /home/pipi/net101/tools/netsim/ansible/templates/bgp/frr.j2] ***
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]

TASK [run vtysh to import bgp config from /home/pipi/net101/tools/netsim/ansible/templates/bgp/frr.j2] ***
changed: [r2]
changed: [r3]
changed: [r1]
changed: [r4]

TASK [Figure out whether to deploy the module vrf on current device] ***********
ok: [r1]
ok: [r2]
ok: [r3]
ok: [dut]
ok: [r4]

TASK [Find configuration template for vrf] *************************************
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]
ok: [dut]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]
ok: [dut] => 
  msg: |-
    vrf configuration for dut
    =========================================
  
    /routing/bgp/vpn add label-allocation-policy=per-vrf vrf=blue route-distinguisher=65000:2 import.route-targets=65000:2 export.route-targets=65000:2 export.redistribute=bgp,connected,ospf,static,vpn
  
    /routing/bgp/template add name=vrf_blue as=65000 output.network=bgp-networks-blue vrf=blue routing-table=blue output.redistribute=connected,bgp,bgp-mpls-vpn,vpn
  
    /routing/bgp/template set vrf_blue router-id=10.0.0.1
  
  
  
  
  
  
    /routing/bgp/connection add template=vrf_blue name=172_16_2_4 remote.address=172.16.2.4 remote.as=65103 comment="r3" address-families=ip local.role=ebgp
  
  
  
  
  
  
  
    /routing/bgp/connection add template=vrf_blue name=172_16_3_5 remote.address=172.16.3.5 remote.as=65104 comment="r4" address-families=ip local.role=ebgp
  
  
  
  
    /routing/bgp/vpn add label-allocation-policy=per-vrf vrf=red route-distinguisher=65000:1 import.route-targets=65000:1 export.route-targets=65000:1 export.redistribute=bgp,connected,ospf,static,vpn
  
    /routing/bgp/template add name=vrf_red as=65000 output.network=bgp-networks-red vrf=red routing-table=red output.redistribute=connected,bgp,bgp-mpls-vpn,vpn
  
    /routing/bgp/template set vrf_red router-id=10.0.0.1
  
  
  
  
  
  
    /routing/bgp/connection add template=vrf_red name=172_16_0_2 remote.address=172.16.0.2 remote.as=65101 comment="r1" address-families=ip local.role=ebgp
  
  
  
  
  
  
  
    /routing/bgp/connection add template=vrf_red name=172_16_1_3 remote.address=172.16.1.3 remote.as=65102 comment="r2" address-families=ip local.role=ebgp

TASK [Find configuration deployment deploy_script for vrf] *********************
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]
ok: [dut]

TASK [Deploy vrf configuration] ************************************************
skipping: [r1]
skipping: [r2]
skipping: [r3]
skipping: [r4]
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/routeros7.yml for dut

TASK [load vrf from /home/pipi/net101/tools/netsim/ansible/templates/vrf/routeros7.j2] ***
ok: [dut]

TASK [Run commands on CHR] *****************************************************
changed: [dut]

PLAY [Deploy custom deployment templates] **************************************
skipping: no hosts matched

PLAY RECAP *********************************************************************
dut                        : ok=28   changed=3    unreachable=0    failed=0    skipped=1    rescued=0    ignored=0   
r1                         : ok=25   changed=5    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   
r2                         : ok=25   changed=5    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   
r3                         : ok=25   changed=5    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   
r4                         : ok=25   changed=5    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   



The device under test has two VRFs with two interfaces in each VRF.
Routers are attached to those interfaces and run BGP with device under test.
Assuming the multi-vrf BGP test case succeeded, this one adds VRF loopback
interfaces advertised into BGP with network statements.

* r1 and r2 should be able to ping each other and rtr VRF loopback
* r3 and r4 should be able to ping each other and rtr VRF loopback
* r1 should not be able to reach r3