Creating Device configuration snippets
[CREATED] dut: initial,ospf
[CREATED] x1: initial,ospf
[CREATED] x2: initial,ospf
Checking Are lab devices ready to be configured?
 [INFO] Checking lab devices with an Ansible playbook
[WARNING]: Could not match supplied host pattern, ignoring: netlab_ready_ssh
[WARNING]: Found variable using reserved name: hosts

PLAY [Wait for SSH servers] ****************************************************
skipping: no hosts matched

PLAY [Wait for device-specific conditions] *************************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [dut]

TASK [Find device readiness script] ********************************************
ok: [dut]

TASK [Wait for device to become ready] *****************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/srsim.yml for dut

TASK [Common SR-OS checks] *****************************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/sros.yml for dut

TASK [Check that required plugin exists, use 'netlab install grpc' to install it] ***
ok: [dut]

TASK [Wait up to 180s for gNMI(TCP 57400) to be ready on 192.168.17.101] *******
ok: [dut -> localhost]

TASK [Update SR-SIM hardware configuration] ************************************
changed: [dut]

TASK [Get port 1/1/c1 status] **************************************************
FAILED - RETRYING: [dut]: Get port 1/1/c1 status (10 retries left).
FAILED - RETRYING: [dut]: Get port 1/1/c1 status (9 retries left).
FAILED - RETRYING: [dut]: Get port 1/1/c1 status (8 retries left).
ok: [dut]

PLAY RECAP *********************************************************************
dut                        : ok=8    changed=1    unreachable=0    failed=0    skipped=0    rescued=0    ignored=0   

Config Deploying device configurations
 [INFO] Executing initial configuration for node x1
 [INFO] Executing initial configuration for node x2
 [INFO] Executing ospf configuration for node x2
 [INFO] Executing ospf configuration for node x1
 [INFO] Starting Ansible playbook to deploy the rest of the
          configurations
[WARNING]: Found variable using reserved name: hosts

PLAY [Deploy initial device configuration] *************************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [dut]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut

TASK [Figure out whether to deploy the module initial on current device] *******
ok: [dut]

TASK [Find configuration template for initial] *********************************
ok: [dut]

TASK [fail] ********************************************************************
skipping: [dut]

TASK [Find configuration deployment deploy_script for initial] *****************
ok: [dut]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [dut] => {
    "msg": "initial configuration for dut\n=========================================\n\n\n\n\n\nupdates:\n- path: configure/card[slot-number=1]\n  val:\n    card-type: iom-1\n    mda:\n    - mda-slot: 1\n      mda-type: me12-100gb-qsfp28\n    - mda-slot: 2\n      mda-type: me12-100gb-qsfp28\n    slot-number: 1\n\n- path: configure/router[router-name=Base]\n  val:\n   ecmp: 64\n\n\n\n\n\n\n- path: configure/router[router-name=Base]/interface[interface-name=system]\n\n  val:\n   admin-state: enable\n   description: \"System interface\"\n   ipv6:\n    address:\n    - ipv6-address: \"2001:db8:1:1::1\"\n      prefix-length: 128\n\n\n\n\n\n- path: configure/port[port-id=1/1/c1]\n  val:\n   admin-state: enable\n   connector:\n    breakout: \"c1-100g\"\n- path: configure/port[port-id=1/1/c1/1]\n  val:\n   admin-state: enable\n   ethernet:\n    mtu: 1514 # max 9800\n    mode: network\n\n\n\n- path: configure/router[router-name=Base]/interface[interface-name=eth-1/1/c1]\n\n  val:\n   admin-state: enable\n   description: \"dut ~ x1 ()\"\n   ip-mtu: 1500\n   port: \"1/1/c1/1\"\n   ipv4:\n    primary:\n     address: \"10.1.0.1\"\n     prefix-length: 30\n\n\n\n\n\n- path: configure/port[port-id=1/1/c2]\n  val:\n   admin-state: enable\n   connector:\n    breakout: \"c1-100g\"\n- path: configure/port[port-id=1/1/c2/1]\n  val:\n   admin-state: enable\n   ethernet:\n    mtu: 1514 # max 9800\n    mode: network\n\n\n\n- path: configure/router[router-name=Base]/interface[interface-name=eth-1/1/c2]\n\n  val:\n   admin-state: enable\n   description: \"dut ~ x2 ()\"\n   ip-mtu: 1500\n   port: \"1/1/c2/1\"\n   ipv4:\n    primary:\n     address: \"10.1.0.5\"\n     prefix-length: 30\n\n   ipv6: { }\n\n\n- path: configure/router[router-name=Base]\n  val:\n    ipv6:\n      router-advertisement:\n        interface:\n        - ip-int-name: eth-1/1/c2\n          admin-state: enable\n          min-advertisement-interval: 3\n          max-advertisement-interval: 5\n\n\n\n\n- path: configure/port[port-id=1/1/c3]\n  val:\n   admin-state: enable\n   connector:\n    breakout: \"c1-100g\"\n- path: configure/port[port-id=1/1/c3/1]\n  val:\n   admin-state: enable\n   ethernet:\n    mtu: 1514 # max 9800\n    mode: network\n\n\n\n- path: configure/router[router-name=Base]/interface[interface-name=eth-1/1/c3]\n\n  val:\n   admin-state: enable\n   description: \"dut ~ stub (stub)\"\n   ip-mtu: 1500\n   port: \"1/1/c3/1\"\n   ipv4:\n    primary:\n     address: \"10.42.1.1\"\n     prefix-length: 24\n\n\n\n\n\n- path: configure/port[port-id=1/1/c4]\n  val:\n   admin-state: enable\n   connector:\n    breakout: \"c1-100g\"\n- path: configure/port[port-id=1/1/c4/1]\n  val:\n   admin-state: enable\n   ethernet:\n    mtu: 1514 # max 9800\n    mode: network\n\n\n\n- path: configure/router[router-name=Base]/interface[interface-name=eth-1/1/c4]\n\n  val:\n   admin-state: enable\n   description: \"dut ~ stub (stub)\"\n   ip-mtu: 1500\n   port: \"1/1/c4/1\"\n   ipv6:\n    address:\n    - ipv6-address: \"2001:db8:cafe:2::1\"\n      prefix-length: 64\n\n\n\n- path: configure/router[router-name=Base]\n  val:\n    ipv6:\n      router-advertisement:\n        interface:\n        - ip-int-name: eth-1/1/c4\n          admin-state: enable\n          min-advertisement-interval: 3\n          max-advertisement-interval: 5\n\n\n\n\n- path: configure/port[port-id=1/1/c5]\n  val:\n   admin-state: enable\n   connector:\n    breakout: \"c1-100g\"\n- path: configure/port[port-id=1/1/c5/1]\n  val:\n   admin-state: enable\n   ethernet:\n    mtu: 1514 # max 9800\n    mode: network\n\n\n\n- path: configure/router[router-name=Base]/interface[interface-name=eth-1/1/c5]\n\n  val:\n   admin-state: enable\n   description: \"dut ~ stub (stub)\"\n   ip-mtu: 1500\n   port: \"1/1/c5/1\"\n   ipv4:\n    primary:\n     address: \"10.42.2.1\"\n     prefix-length: 24\n\n   ipv6:\n    address:\n    - ipv6-address: \"2001:db8:cafe:3::1\"\n      prefix-length: 64\n\n\n\n- path: configure/router[router-name=Base]\n  val:\n    ipv6:\n      router-advertisement:\n        interface:\n        - ip-int-name: eth-1/1/c5\n          admin-state: enable\n          min-advertisement-interval: 3\n          max-advertisement-interval: 5\n\n\n"
}

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/sros.yml for dut

TASK [Generate gNMI YAML configuration] ****************************************
ok: [dut]

TASK [Update initial node configuration from gNMI template /work/netlab_cicd/node_files/dut/initial] ***
changed: [dut]

TASK [debug] *******************************************************************
skipping: [dut]

PLAY [Deploy module-specific configurations] ***********************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [dut]

TASK [Deploy individual configuration modules] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut => (item=ospf)

TASK [Figure out whether to deploy the module ospf on current device] **********
ok: [dut]

TASK [Find configuration template for ospf] ************************************
ok: [dut]

TASK [fail] ********************************************************************
skipping: [dut]

TASK [Find configuration deployment deploy_script for ospf] ********************
ok: [dut]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [dut] => {
    "msg": "ospf configuration for dut\n=========================================\n\n\n\n\nupdates:\n\n\n- path: configure/router[router-name=Base]/ospf[ospf-instance=0]\n\n  val:\n    admin-state: enable\n    router-id: 10.0.0.1\n    area:\n    - area-id: \"0.0.0.0\"\n      interface:\n      - interface-name: \"eth-1/1/c1\"\n        interface-type: \"point-to-point\"\n      - interface-name: \"eth-1/1/c3\"\n        passive: True\n      - interface-name: \"eth-1/1/c5\"\n        passive: True\n    - area-id: \"0.0.0.2\"\n      interface:\n      - interface-name: \"eth-1/1/c2\"\n        interface-type: \"point-to-point\"\n\n\n\n- path: configure/router[router-name=Base]/ospf3[ospf-instance=0]\n\n  val:\n    admin-state: enable\n    router-id: 10.0.0.1\n    area:\n    - area-id: \"0.0.0.0\"\n      interface:\n      - interface-name: \"system\"\n      - interface-name: \"eth-1/1/c4\"\n        passive: True\n      - interface-name: \"eth-1/1/c5\"\n        passive: True\n    - area-id: \"0.0.0.2\"\n      interface:\n      - interface-name: \"eth-1/1/c2\"\n        interface-type: \"point-to-point\"\n\n"
}

TASK [Deploy ospf configuration] ***********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/sros.yml for dut

TASK [Generate gNMI YAML configuration] ****************************************
ok: [dut]

TASK [Update ospf node configuration from gNMI template /work/netlab_cicd/node_files/dut/ospf] ***
changed: [dut]

TASK [debug] *******************************************************************
skipping: [dut]

PLAY [Deploy custom deployment templates] **************************************
skipping: no hosts matched

PLAY RECAP *********************************************************************
dut                        : ok=18   changed=2    unreachable=0    failed=0    skipped=4    rescued=0    ignored=0   

Results of configuration script deployments
================================================================================
x1               Script:  initial,ospf
x2               Script:  initial,ospf


This lab tests the dual-stack multi-area OSPFv2/OSPFv3 deployments. The device under test has
an IPv4 stub interface, an IPv6 stub interface, a dual-stack stub interface, an IPv4-only link,
and a dual-stack link.