[WARNING]: Invalid characters were found in group names but not replaced, use -vvvv to see details [WARNING]: Could not match supplied host pattern, ignoring: unprovisioned PLAY [Deploy initial device configuration] ************************************* TASK [Set variables that cannot be set with VARS] ****************************** ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Find device readiness script] ******************************************** ok: [h1] ok: [h2] ok: [h4] ok: [h3] ok: [s1] TASK [Wait for device to become ready] ***************************************** skipping: [h1] skipping: [h2] skipping: [h3] skipping: [h4] included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/vjunos-router-clab.yml for s1 TASK [Wait for SSH server] ***************************************************** included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/vm-clab-ssh-check.yml for s1 TASK [Check if 'sshpass' is installed] ***************************************** ok: [s1 -> localhost] TASK [Check for 'timeout' command] ********************************************* ok: [s1 -> localhost] TASK [Execute local ssh command to check vjunos-router readiness] ************** FAILED - RETRYING: [s1 -> localhost]: Execute local ssh command to check vjunos-router readiness (60 retries left). FAILED - RETRYING: [s1 -> localhost]: Execute local ssh command to check vjunos-router readiness (59 retries left). FAILED - RETRYING: [s1 -> localhost]: Execute local ssh command to check vjunos-router readiness (58 retries left). FAILED - RETRYING: [s1 -> localhost]: Execute local ssh command to check vjunos-router readiness (57 retries left). FAILED - RETRYING: [s1 -> localhost]: Execute local ssh command to check vjunos-router readiness (56 retries left). FAILED - RETRYING: [s1 -> localhost]: Execute local ssh command to check vjunos-router readiness (55 retries left). ok: [s1 -> localhost] TASK [Confirm s1 SSH server works] ********************************************* ok: [s1] => msg: Node s1 is ready. TASK [Wait for ge-0/0/0 interface] ********************************************* included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/vjunos-switch.yml for s1 TASK [Wait for ge-0/0/0 to appear] ********************************************* ok: [s1] TASK [Deploy initial configuration] ******************************************** included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for h1, h2, h3, h4, s1 TASK [Figure out whether to deploy the module initial on current device] ******* ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Find configuration template for initial] ********************************* ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [fail] ******************************************************************** skipping: [h1] skipping: [h2] skipping: [h3] skipping: [h4] skipping: [s1] TASK [Print deployed configuration when running in verbose mode] *************** ok: [h2] => msg: |- initial configuration for h2 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing, create any bond devices # ip link set dev eth1 up set +e ip addr del 172.16.0.2/24 dev eth1 2>/dev/null set -e ip addr add 172.16.0.2/24 dev eth1 ip link set eth1 mtu 1500 # # Add static routes (usually IPv4 routes pointing to the first usable gateway) # # # # # Print the final routing table ip route ok: [h1] => msg: |- initial configuration for h1 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing, create any bond devices # ip link set dev eth1 up set +e ip addr del 172.16.0.1/24 dev eth1 2>/dev/null set -e ip addr add 172.16.0.1/24 dev eth1 ip link set eth1 mtu 1500 # # Add static routes (usually IPv4 routes pointing to the first usable gateway) # # # # # Print the final routing table ip route ok: [h3] => msg: |- initial configuration for h3 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing, create any bond devices # ip link set dev eth1 up set +e ip addr del 172.16.1.3/24 dev eth1 2>/dev/null set -e ip addr add 172.16.1.3/24 dev eth1 ip link set eth1 mtu 1500 # # Add static routes (usually IPv4 routes pointing to the first usable gateway) # echo Removing existing IPv4 routes while ip route del 172.16.0.0/16 2>/dev/null; do : ; done while ip route del 10.0.0.0/24 2>/dev/null; do : ; done while ip route del 10.1.0.0/16 2>/dev/null; do : ; done while ip route del 10.2.0.0/24 2>/dev/null; do : ; done # # echo Adding direct static routes ip route add 172.16.0.0/16 via 172.16.1.5 dev eth1 protocol static ip route add 10.0.0.0/24 via 172.16.1.5 dev eth1 protocol static ip route add 10.1.0.0/16 via 172.16.1.5 dev eth1 protocol static ip route add 10.2.0.0/24 via 172.16.1.5 dev eth1 protocol static # # Print the final routing table ip route ok: [h4] => msg: |- initial configuration for h4 ========================================= #!/bin/bash # # This script contains the 'ip' commands needed to set up container # interfaces and route table. It's executed within the container # network namespace on the container host. # # /etc/hosts file is generated as a clab bind. # set -e ### One-Shot configuration (non-Ubuntu VM or container) # # Disable IPv4 and IPv6 forwarding # sysctl -w net.ipv4.ip_forward=0 sysctl -w net.ipv6.conf.all.forwarding=0 # # Interface addressing, create any bond devices # ip link set dev eth1 up set +e ip addr del 172.16.2.4/24 dev eth1 2>/dev/null set -e ip addr add 172.16.2.4/24 dev eth1 ip link set eth1 mtu 1500 # # Add static routes (usually IPv4 routes pointing to the first usable gateway) # echo Removing existing IPv4 routes while ip route del 172.16.0.0/16 2>/dev/null; do : ; done while ip route del 10.0.0.0/24 2>/dev/null; do : ; done while ip route del 10.1.0.0/16 2>/dev/null; do : ; done while ip route del 10.2.0.0/24 2>/dev/null; do : ; done # # echo Adding direct static routes ip route add 172.16.0.0/16 via 172.16.2.5 dev eth1 protocol static ip route add 10.0.0.0/24 via 172.16.2.5 dev eth1 protocol static ip route add 10.1.0.0/16 via 172.16.2.5 dev eth1 protocol static ip route add 10.2.0.0/24 via 172.16.2.5 dev eth1 protocol static # # Print the final routing table ip route ok: [s1] => msg: |- initial configuration for s1 ========================================= system { host-name s1; static-host-mapping { h1 inet 172.16.0.1; h2 inet 172.16.0.2; h3 inet 172.16.1.3; h4 inet 172.16.2.4; } } interfaces { ge-0/0/0 { flexible-vlan-tagging; native-vlan-id 700; } ge-0/0/0.0 { vlan-id 700; } ge-0/0/1 { flexible-vlan-tagging; native-vlan-id 700; } ge-0/0/1.0 { vlan-id 700; } ge-0/0/2 { flexible-vlan-tagging; native-vlan-id 701; } ge-0/0/2.0 { vlan-id 701; } ge-0/0/3 { flexible-vlan-tagging; native-vlan-id 702; } ge-0/0/3.0 { vlan-id 702; } } interfaces { ge-0/0/0 { mtu 1522; } ge-0/0/1 { mtu 1522; } ge-0/0/2 { mtu 1522; } ge-0/0/3 { mtu 1522; } lo0.0 { family inet { address 10.0.0.5/32; } } ge-0/0/0.0 { description "[Access VLAN red] s1 -> h1"; } ge-0/0/1.0 { description "[Access VLAN red] s1 -> h2"; } ge-0/0/2.0 { description "[Access VLAN blue] s1 -> h3"; } ge-0/0/3.0 { description "[Access VLAN green] s1 -> h4"; } irb.700 { description "VLAN red (700) -> [h1,h2] [stub]"; } irb.701 { description "VLAN blue (701) -> [h3] [stub]"; family inet { address 172.16.1.5/24; } } irb.702 { description "VLAN green (702) -> [h4] [stub]"; family inet { address 172.16.2.5/24; } } } protocols { lldp { interface fxp0 { disable; } interface all; } } TASK [Find configuration deployment deploy_script for initial] ***************** ok: [h1] ok: [h2] ok: [h3] ok: [h4] ok: [s1] TASK [Deploy initial configuration] ******************************************** included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/linux-clab.yml for h1, h2, h3, h4 included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/junos.yml for s1 TASK [Define script filename and determine whether to execute in netns] ******** ok: [h1] ok: [h2] ok: [h3] ok: [h4] TASK [Create a temporary file for the rendered script] ************************* changed: [h1 -> localhost] changed: [h3 -> localhost] changed: [h4 -> localhost] changed: [h2 -> localhost] TASK [Create container setup script from /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2] *** changed: [h2 -> localhost] changed: [h3 -> localhost] changed: [h4 -> localhost] changed: [h1 -> localhost] TASK [Copy script into running container at /tmp/config-h1_initial.sh] ********* skipping: [h1] skipping: [h2] skipping: [h3] skipping: [h4] TASK [Execute /tmp/config-h1_initial.sh to deploy initial config based on /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2] *** skipping: [h1] skipping: [h2] skipping: [h3] skipping: [h4] TASK [Container configuration for initial based on /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2 executed in netns] *** changed: [h2 -> localhost] changed: [h1 -> localhost] changed: [h3 -> localhost] changed: [h4 -> localhost] TASK [Remove temporary file /tmp/h1_initial-o93cadqz.sh] *********************** changed: [h1 -> localhost] changed: [h2 -> localhost] changed: [h3 -> localhost] changed: [h4 -> localhost] TASK [junos_config: deploying initial from /home/pipi/net101/tools/netsim/ansible/templates/initial/junos.j2] *** changed: [s1] PLAY [Deploy module-specific configurations] *********************************** TASK [Set variables that cannot be set with VARS] ****************************** ok: [s1] TASK [Deploy individual configuration modules] ********************************* included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for s1 => (item=vlan) TASK [Figure out whether to deploy the module vlan on current device] ********** ok: [s1] TASK [Find configuration template for vlan] ************************************ ok: [s1] TASK [fail] ******************************************************************** skipping: [s1] TASK [Print deployed configuration when running in verbose mode] *************** ok: [s1] => msg: |- vlan configuration for s1 ========================================= interfaces { ge-0/0/0 { encapsulation flexible-ethernet-services; } ge-0/0/0.0 { encapsulation vlan-bridge; } ge-0/0/1 { encapsulation flexible-ethernet-services; } ge-0/0/1.0 { encapsulation vlan-bridge; } ge-0/0/2 { encapsulation flexible-ethernet-services; } ge-0/0/2.0 { encapsulation vlan-bridge; } ge-0/0/3 { encapsulation flexible-ethernet-services; } ge-0/0/3.0 { encapsulation vlan-bridge; } } bridge-domains { vlan-701 { domain-type bridge; vlan-id 701; routing-interface irb.701; interface ge-0/0/2.0; } vlan-702 { domain-type bridge; vlan-id 702; routing-interface irb.702; interface ge-0/0/3.0; } vlan-700 { domain-type bridge; vlan-id 700; routing-interface irb.700; interface ge-0/0/0.0; interface ge-0/0/1.0; } } TASK [Find configuration deployment deploy_script for vlan] ******************** ok: [s1] TASK [Deploy vlan configuration] *********************************************** included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/junos.yml for s1 TASK [junos_config: deploying vlan from /home/pipi/net101/tools/netsim/ansible/templates/vlan/vjunos-router.j2] *** changed: [s1] PLAY [Deploy custom deployment templates] ************************************** skipping: no hosts matched PLAY RECAP ********************************************************************* h1 : ok=13 changed=4 unreachable=0 failed=0 skipped=4 rescued=0 ignored=0 h2 : ok=13 changed=4 unreachable=0 failed=0 skipped=4 rescued=0 ignored=0 h3 : ok=13 changed=4 unreachable=0 failed=0 skipped=4 rescued=0 ignored=0 h4 : ok=13 changed=4 unreachable=0 failed=0 skipped=4 rescued=0 ignored=0 s1 : ok=25 changed=2 unreachable=0 failed=0 skipped=2 rescued=0 ignored=0 The device under test is a mixed layer-2/layer-3 switch. Red VLAN is a layer-2-only VLAN, the device acts as a L2/L3 switch on all other VLANs h1 and h2 should be able to ping each other, but not h3 or h4 h3 and h4 should be able to ping each other, but not h1 or h2